Potato Cold Storage: Temperature, Humidity & Design Requirements

Potato Cold Storage: Temperature, Humidity & Design Requirements

Potato Cold Storage: Temperature, Humidity & Design Requirements

Potatoes are not regular cold room loads. The potato tubers are living organisms and must remain dormant for approximately ten months, be humid while avoiding immersion in water, and be stacked on floors constructed for heavy loads. An incorrect setpoint, airflow or chamber layout will be reflected visible months later which will be in terms of sprouted, sweet or rotten material. This guide provides the design parameters for cold storage of potatoes in India, including temperature, humidity, chamber layout, ventilation, defects and capacity. The guide relies on NHB technical specifications and ICAR-CPRI Shimla recommendations.

Why potatoes need specialized cold storage

India is the second-largest producer of potatoes across the globe, and much of the northern plains potato crop is harvested from the end of winter until March, just before the weather becomes extremely hot, with the temperature surpassing 40°C. If the tubers are not cold, they would wake up from dormancy and start sprouting, shriveling, and rotting long before the market gets ready for them. The storage facility for potatoes must keep the harvest until about October.

Three things separate potatoes from a general-purpose cold room load:

  • They are alive. Tubers continue to breathe and produce heat that must be removed by the refrigeration plant constantly. This is also true for warm storage, as it speeds up the process of coming out of dormancy.
  • End use sets the setpoint. Different temperatures are required for seed, table, and processing potatoes. A store set for one variety may be dangerous for others.
  • Moisture cuts both ways. When humidity is high, evaporation of moisture from tubers is minimized, but if free moisture is present on the surface of tubers, it may lead to rot.

The pre-storage processing also plays a vital role. Sorting or grading prior to loading eliminates any cut, fresh, or rotten potatoes so that one spoiled bag doesn't ruin all the potatoes in a storage room. Size sorting also helps store managers to plan removals later on since marketers of seed, table or processing potatoes will normally require different grades at different times.

That is why potato storage is designed in a particular way, being commodity-specific instead of generic cold storage. The size of a chamber, its floor load, cooling coils dimensions, humidification, and CO2 control are all determined by the nature of potatoes and will be discussed in the next sections.

Temperature and humidity requirements

The correct temperature must also depend on how the potatoes will be utilized. The NHB specified conditions described below conform to the recommendations of CPRI concerning the handling of seed potatoes and are supported by internationally approved potato storage data.

End use Holding temperature Relative humidity Storage period Key condition
Early crop (immature)4–10°C95%Up to 3 monthsOnly if cured before storage
Seed potato3 ± 1°C90–95%5–10 monthsRapid cooling is acceptable; keep away from sprout-suppressant areas
Table (ware) potato2–4°C (NHB design value: 4°C)90–95%5–10 monthsCold holding raises sugars; fine for cooking, less so for frying
Processing: French fries10–12°C*90–95%1–10 monthsSprout suppressant needed for long storage
Processing: chips10–12°C*90–95%1–8 monthsAvoid cold-induced sweetening

*NHB's table lists 7.2–10°C for processing potatoes and notes that CPRI recommends about 11 ± 1°C. ICAR-CPRI studies on Indian processing cultivars hold tubers near 12°C with a sprout suppressant. Confirm the final setpoint against your processor's sugar specification.

Temperature and humidity are only part of the specification. The operating parameters below decide whether the setpoints are actually achieved.

  • Curing: keep tubers at 15–20°C and 90–95% RH for 5–10 days before cold storage so skin wounds heal. NHB advises harvesting at tuber temperatures between 8°C and 20°C.
  • Loading rate: 4–5% of total capacity per day, split equally across chambers.
  • Pull-down for table and processing lots: cool to 15°C within 24 hours, then lower by about 0.5°C per day toward the holding temperature.
  • Pull-down for seed: cool to 10°C within 24 hours, then to 3 ± 1°C within 8–10 days.
  • Control band: ±1°C on temperature, and chambers kept dark.

Single-chamber vs multi-chamber design

According to NHB guidelines, a minimum of two chambers is required, each roughly comprising 1000-1500 MT. Although looking economical on paper, a single large chamber sacrifices control.

Factor Single large chamber Multi-chamber (1,000–1,500 MT each)
Temperature uniformityLong air throw; hot and cold spotsEasier to hold within ±1°C
Lot separationOne setpoint for all stockSeed, table and processing lots kept apart
Loading and unloadingEntire store disturbedOne chamber opened at a time
Part-load efficiencyPlant sized for one large loadCompressors staged as chambers empty
Failure riskOne fault endangers all stockFault stays within one chamber

The second argument is about efficiency; it is known that the carrying load is about 50% of the maximum load. This means that a facility designed with chambers and compressor stages can continuously adjust to meet various load requirements throughout the season.

The majority of potato stores in India are multi-level with the chambers having a mezzanine level. The construction of inter-floors must have the capacity of carrying a load of 900 kg/m². The staircases can be constructed in the ante-chamber, so that all storage space can be utilized and it could also provide space for lifts and escape in case of emergencies. If a chamber will have potato lots treated with the chemical for preventing sprouting, it must be distinct from chambers containing the seed potatoes with its own ante-room.

Multi-chamber design is also beneficial for commercial flexibility. A four-chamber store may operate one chamber at 3°C for seed potatoes, two chambers for table potatoes, and one for processing stock at a higher temperature, and be able to change this distribution from one season to another according to customer needs. NHB also advises on multi-commodity usage so that the chambers don't remain unused all season.

The insulation is designed on the basis of NHB specifications that ensure that heat load remains low even at a temperature range of -4°C to +2°C. The thicknesses considered are 100 mm PUF or 150 mm EPS above exposed walls and roofs and a vapor barrier is provided on the warm side of the insulation.

Ventilation and air circulation

Potato stores fail on airflow more often than on refrigeration capacity. Four design points matter most.

  • Air circulation: Minimum allowable air flow is 50 CFM per MT (50 to 70 m³/h per MT) during loading and pull-down when heat load is at its maximum. During holding period fans work at approximately 70% speed, resulting in about 30% fan power consumption while still keeping bearing temperature ±1°C. NHB's reference design is based on using from three to four air cooling units per chamber, with air ducts located at the top to provide uniform air distribution over the chamber.
  • Coil selection for humidity: The gap in temperatures between the air humidity and evaporating refrigerant should be maintained small, approximately 2.2-4.4 °C , which means utilizing big coils with fins distance of 6.25-8.5 mm. The higher temperature gap causes drying air and shrinkage of tubers indicating that one of the decisive factors for stock quality is the kind of refrigeration units used for cold storage.
  • Humidification: above 90% RH, add a fogger producing 2–10 micron mist, distributed so tubers stay dry.
  • Fresh air: The desired air exchange rate is usually 2 to 6 changes per day; CO₂ concentration is kept below 4,000 ppm during loading and 2,000 ppm during holding, by means of CO₂ sensors. NHB prefers mechanical ventilation with energy recovery, rather than the usual practice of operating doors and hatches, which wastes energy, changes temperature, and saturates the product.

The loading process is significant. Fresh potato tubers come warm, with temperature ranging from 20°C to 25°C in Northern plains. The process of sprouting produces higher respiration heat than any other time. The pull-down process should be fast, and airflow should be uniform. Otherwise, while some pallets might cool down, others remain warm for longer. Operating fans at full speed until the desired temperature is achieved is the best practice to save quality and energy.

Stacking components is very important as well. Create enough space so the air circulation is able to reach all bags and install sensors according to the recommendations of NHB- one sensor per 100 tons of product.

Common storage defects and prevention

Most potato storage losses trace back to a design or operating parameter above. The chart below links each defect to its cause and fix.

Defect Typical cause Prevention
SproutingHolding temperature too high; long storage; slow initial coolingHold seed and table lots at 3–4°C. For processing lots at 10–12°C, apply a sprout suppressant about 30 days after loading, per CPRI advice
Cold-induced sweeteningProcessing varieties held at table-potato temperaturesStore processing lots at 10–12°C; avoid rapid cooling
Greening and glycoalkaloid build-upLight exposure in chambers or during handlingDark chambers; no daylight at loading docks; sort out green tubers
Weight loss and shrivellingRH below 90%; high coil temperature difference; excess airflow90–95% RH, low-ΔT coils, fogger humidification
Soft rot and wet rotWounded or uncured tubers; condensation; wet productCure 5–10 days; sort and grade before loading; avoid wetting from fog or door condensation
Black heartPoor aeration and CO₂ build-up inside dense stacks2–6 air changes per day; CO₂ control; stack with air gaps
Freezing damageOvercold coil discharge; local cold spotsHold the control band; use multiple sensors; check air distribution

Over and above being a design element, prevention is also part of the operational routine. Each chamber must have its temperature, humidity, and CO₂ logged regularly. Sample collecting bags should regularly be sent during the holding time to determine the presence of rot and sprouting. The chamber should be promptly attended to if it is not performing properly since it will cost much less to repair it within the first few weeks than to dispose of that chamber of inferior quality in September.

Glycoalkaloids: tubers that are exposed to light become green and gain glycoalkaloids like solanine, which has a bitter taste and is not desirable in food. Covering the tubers during storage and handling is a practical measure against glycoalkaloids.

Capacity planning for potato cold storage

The worked example below follows NHB's reference chamber for a 5,000 MT, four-chamber potato store using 50 kg bags.

Step Calculation Result
Chamber volume20 m × 17 m × 12.5 m4,250 m³
Chamber capacity4,250 m³ ÷ 3.4 m³ per MT1,250 MT
Bags per chamber1,250,000 kg ÷ 50 kg25,000 bags
Total capacity4 chambers × 1,250 MT5,000 MT
Daily loading4–5% of 5,000 MT200–250 MT/day (about 20–25 days to fill)
Respiration heat at 3°C1,250,000 kg × 0.018 W/kg22.5 kW per chamber
Respiration heat at 15°C1,250,000 kg × 0.027 W/kg33.75 kW per chamber

Respiration rates from ASHRAE data as used in NHB's reference calculation. Illustrative only; not a substitute for a site-specific load calculation.

Respiration constitutes a significant proportion of the loading demand, as shown in NHB's calculations for Delhi, which reveals that a chamber weighing 1,250 MT at a temperature of 3°C utilizes approximately 41.8 kW of energy for inertia purposes, over 50% of which is related to respiration. Thus, a reference plant with a total capacity of 5,000 MT will need approximately 340-370 kW of refrigeration power, which is determined by the loading as well as cooling period. Of course, real cases depend on actual conditions in their locations, incoming potato temperature, and the combination of seed, table and production stocks.

The planning for capacity starts from the chambers; but it cannot end there either. Think about the need for a pre-chamber area, a sorting and grading area, a reload area, a machine room, and a standby electricity source. The potato storage period is a committed time frame of 5 to 10 months for potatoes, and prolonged power breakdowns in this period can lead to losses of the entire inventory. Plan the mix of chambers, as well. You have to decide on the amount by which each type of potato shall be stored even before sizing the refrigeration plant, as they require various sprout-suppressing storage temperatures, areas, and cooling profiles.

If you are still deciding between a cold room and a full cold store, our cold room guide explains how sizing and cost change with scale.

FAQs

What is the ideal temperature for potato storage?

Factors like temperature and moisture have an effect on the storage of seed potatoes and table potatoes. Seed potatoes are maintained at 3 ± 1°C while table potatoes are stored at 2–4°C. Meanwhile, processing potatoes intended for chips and fries are stored at warmer temperatures of around 10–12°C with the use of a sprout-suppressing agent to avoid sweetness from being induced by cold.

How long can potatoes be stored in cold storage?

NHB guidelines state the storage duration for seed and table potatoes at 5–10 months, cured early crop potatoes at 3 months, and chipping potatoes (up to 10 months for French Fries) with the use of sprout-suppressing agents at 1–8 months. The common practice in northern India is to load stores between February and March and unloading occurs between October and November.

What humidity is needed for potato cold storage?

Use low-temperature-difference coils to maintain relative humidity between 90–95%. If it is necessary to exceed the 90% limit, implementation of fogging is required to avoid wetness of tubers.

Conclusion

The success or failure when it comes to cold potato storage mostly depends on the parameters selected at the design stage. Store seed potatoes at 3 ± 1°C, table potatoes at 2–4°C, keep processing lots at 10–12°C with a sprout inhibitor, and maintain relative humidity of 90–95% using low-temperature-difference coils. It is necessary to include in the design at least two rooms of 1,000–1,500 MT, and all airflow and fresh-air systems should be expected for both loading and holding stages. Once these specifications are satisfied, the failures illustrated in the chart above can be avoided.

Planning a potato cold store? Singhania Refrigeration helps investors, FPOs and operators work through chamber layout, insulation and refrigeration for commodity-specific stores.
Discuss your potato cold storage project with our team →

References: National Horticulture Board, Technical Standards for Cold Storages, Type 01 (NHB-CS-Type 01-2010), nhb.gov.in; ICAR guidelines and published research on potato storage; ICAR-CPRI (Central Potato Research Institute), Shimla, storage recommendations.

Call Now